Sourcing & compliance · Container loading
How many boneless sofas fit in a 20GP or 40HQ container?
Carton CBM decides how many compressed sofas fit in a container — but the loading plan decides how much of that you actually get. Here is how to size a first order and how to read a supplier's loading plan.
Published 2026-09-22 · 5 min read
Divide container CBM by carton CBM and you get a theoretical maximum. That number is useful for a first estimate and misleading for a purchase order. What you actually buy is decided by the loading plan, which is a carton-level packing arrangement — and it is the one document worth insisting on before you pay a deposit.
What are the reference volumes for a 20GP and a 40HQ?
Internal dimensions are what decide how many cartons go in. Use these as planning figures, then confirm against the container your forwarder actually books:
| Container | Internal L × W × H | Nominal volume | Door opening | Max payload |
|---|---|---|---|---|
| 20GP | 5.90 × 2.35 × 2.39 m | 33.2 CBM | 2.34 × 2.28 m | ~28,200 kg |
| 40GP | 12.03 × 2.35 × 2.39 m | 67.7 CBM | 2.34 × 2.28 m | ~26,700 kg |
| 40HQ | 12.03 × 2.35 × 2.70 m | 76.4 CBM | 2.34 × 2.58 m | ~26,460 kg |
| 45HQ | 13.55 × 2.35 × 2.70 m | 86 CBM | 2.34 × 2.58 m | ~25,600 kg |
None of those volumes is a loading figure. A carton is a solid box, so what fits is decided by how the box divides into the container's length, width and height — and by three limits that a volume quotient ignores completely:
- The leftover strip. A 40 cm carton divides four times into a 2.35 m width with 75 cm spare, and that 75 cm holds nothing. The same carton in a 50 cm width wastes less. Same volume, different carton count.
- The door opening. A 40HQ is 2.70 m high inside but only 2.58 m at the door. A carton taller than the door never gets into the box, however well it would fit once inside.
- Payload. Furniture is light, so this rarely binds — but a dense, small-carton model can hit the weight limit before the volume limit.
Everything on this site is therefore packed carton by carton against those internal dimensions, with 40 mm left at the ceiling and 200 mm at the door end for lashing, instead of dividing 28 or 68 CBM by a carton volume. The result is usually below a straight volume division. That gap is not pessimism, it is the strip you cannot fill.
How do I calculate the carton count for a mixed order?
Multiply, then check the plan.
- For each model, take carton CBM from the specification sheet.
- Multiply by the quantity you want of that model → model CBM.
- Sum all models → total order CBM.
- Compare the total against the container's usable volume.
Worked example for a first order that tests three seat sizes:
| Model | Carton CBM | Qty | Model CBM |
|---|---|---|---|
| K-01 3-seater | 0.179 | 80 | 14.32 |
| K-02 2-seater | 0.16 | 60 | 9.60 |
| K-05 armchair | 0.14 | 120 | 16.80 |
| Total | 260 pcs | 40.72 CBM |
40.72 CBM sits comfortably inside a 40GP, or leaves a 40HQ with room for two more models. That is the more useful way to read the number: the same order is a tight fit in one container and a comfortable one in the next size up, and the freight quote for each tells you which is cheaper per unit rather than per container.
Why is a carton-level loading plan worth insisting on?
Because mixed orders lose space, and the loss is invisible until you open the doors.
When carton sizes differ — a 0.77 CBM sectional carton next to 0.024 CBM pouf cartons — the last metre of the container fills with gaps. A supplier who simply sums CBM will quote you a full container and load a partial one, and the difference comes out of your margin, not theirs.
A proper loading plan shows:
- Every carton placed, with count per stack
- Total CBM achieved and the void space left over
- Which cartons go in the door and which go deep (order of unloading matters if you have multiple destination warehouses)
- Total gross weight, checked against the road weight limit at the destination
Ask for it before the deposit, not after production. If it arrives as a spreadsheet with carton-level rows, the supplier is planning. If it arrives as a single number, they are guessing.
What is the sensible size for a first order?
Small enough to test the product, large enough to make the freight per unit sensible.
For a new importer, a first order usually looks like three or four models across one container, weighted toward the model you expect to sell most. That does two things: it puts real stock in front of customers, and it generates your own cost data — actual freight per unit, actual damage rate, actual sell-through — which is a better basis for the second order than anything a supplier tells you.
Mixed-SKU loading is accepted on our orders. The minimum is ten pieces per model at the wholesale price, and an order below that is still taken as a sample at the sample price with the fee credited back against your first 20GP — so you can put one unit of a model in the container to test it, and give the rest of the space to what you expect to sell.
How much does compression actually matter inside the container?
It changes the unit economics, not just the packing.
Take the 40HQ as the comparison. At shipped volume a 40HQ takes 349 pcs of K-01. The same sofa, had it shipped assembled at its expanded 1.152 CBM, would have allowed roughly 54 pcs in the same container.
Roughly six times the stock, one container, the same freight invoice. The rest of the difference — warehousing, last-mile, returns — follows from the same construction choice.